Tips On How To Extend Smok Pen Recharge Time
The Smok Pen is a new pen that was developed by two guys in California. They wanted to create a cool writing instrument that looked like a genuine pen but had the ability to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has taken the marketplace by storm.
The Smok Pen includes a built quality that is just great. I found that even though it can be an electronic pen the build quality is simply as good as the pens that I have reviewed. This is because of how they made the most notable cap. You don’t have to be worried about the cap cracking or breaking on you Smok Valve Pen.
The two biggest differences that separate the Smok Valve from other pens may be the form of the coils and the way that they are built. Generally the coil on a Smok Pen is larger than on other pens. I think that they did this deliberately, to help make the pen feel bigger.
Invest the a glance at a Smok Pen, you will notice that your body of the pen is round rather than smooth like other pens. On the trunk of the pen there is a little tab that houses the coil. Once you press on the tab you can easily turn the heating element on / off. I must say i liked this podsmall.com feature since it allows me to use the Smok Pen 22 whenever I feel like smoking.
To use the Smok Pen it is advisable to keep the heat button pressed. Once the button is pressed, the heating element will begin to warm up. Once it reaches the appropriate temperature it is possible to switch off the heating element. Smok recommends utilizing a 22mm tank. I prefer a larger tank, but that’s just me.
When you put your Smok Pen in to the tank you will notice a indicator light come on. The indicator light will remain green unless you put your Smok Pen in to the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is very important always put your pen in to the charger before you apply the e-liquids to the coil heads. Additionally it is important to do this before putting your e-liquids into the coil heads.
Once you have completed this step, you should always check to see in case you are at the proper temperature for the coils to fire. Or even then you should turn the power off and try again. If you are still not satisfied with your Smok Pen i quickly suggest you take it set for some troubleshooting. This is what I’d call the “troubleshooting process” because sometimes things just usually do not work as they should. It is suggested that you perform the next two steps, then go ahead and check the Smok Pen to see if it still gets the electronic charging port.
Prior to going any further you should take away the battery from your own pen and unscrew the magnetic cap. You should then take away the plastic sleeve that holds the sub-ohm. You will find a wire that runs through the Smok’s body that is green in color. You need to loosen this wire using pliers. Once you have loosened this wire you can then access the sub-ohm. You need to then remove the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch any of the coils.
When you have placed the sub-ohm tank in to the pen you need to then place the rest of the components including the wattage, the batteries and the heating element into the included microwaveable microwave oven. Start the energy and follow the on screen instructions. You should place the pen’s battery into the microwave and activate the setting. You should then wait approximately 30 seconds before turning it cool off. When you first put the pen into the microwave the electronic reading will show a minimal voltage protection setting. If this setting will not automatically get set then you should follow the on screen instructions.
Once the Smok Pen has reached the temperature that it needs to reach you need to then connect both wires to the positive and negative on the positive post on the Smok unit. You should then connect another end of the battery to the negative post on the negative side of the Smok unit. The final step is to connect the positive cable to the bottom of the Smok’s on / off switch.
After all the components have been placed into the pen, you should turn the energy on. Following the first test run, you ought to be able to see the battery life indicator light come on. If you don’t see any sign of life from the Smok Pen, you need to remove the battery from the pen and replace it with a fresh one. For your convenience gleam green light which might be pressed so that you can confirm the battery charging status. If you have done these things and you do not see the green light indicating charging, you need to replace the battery.